*-1,A
	     FATAL ERROR !
	     Error No. 001
      RSS Program File Corrupted.
    Restore RSS From Backup Disks.
*-2,A

     Could Not Write File to Disk.


*-3,A

	    File Not Found.


*-4,A

    Could Not Read File From Disk.


*-5,A

       Could Not Find Directory.


*-6,A

	     Invalid Path
	    Name Not Found.

*-7,A


	Empty Directory Found.

*-8,A

	     Invalid Path
	   Not a Directory.

*-9,A
		 ERROR

      'HELP.TXT' File Not Found.

*-10,A
	     FATAL ERROR !
	     Error No. 010
   Choice List File Is Corrupted Or
    Entry Not Found In Choice List.
*-11,A
	     FATAL ERROR !
	     Error No. 011
     Can't Find RSS Library File.
     'ENTERP.VVD' File Is Missing.
*-12,A
	     FATAL ERROR !
	     Error No. 012
     Can't Display Desired Screen.
       Corrupt Or Missing File.
*-13,A
	  Not Enough Memory!
     You Must Delete Some Entries
      From Codeplug To Continue.

*-14,A
	     FATAL ERROR !
	     Error No. 014
	Could Not Access Field.
       Corrupt Or Missing File.
*-15,A
	     FATAL ERROR !
	     Error No. 015
      Could Not Load Choice List.
     'CLIST.TXT' File Is Missing.
*-16,A
	     Error No. 016

	Serial Port Buffers Not
    Allocated To Send/Receive Data.
*-17,A
	     Error No. 017

    Serial Port Buffers Overflowed.
	Try Sending File again.
*-18,A
	     Error No. 018

	 Communications Error.
      Possible Hardware problem.
*-19,A
	     Error No. 019

	 Serial Port Is Busy.
	      Try again.
*-20,A
	     Error No. 020

      Possible PC Hardware Error.
     Cannot Write To Serial Port.
*-21,A
       Connected Device Error:
	Wrong Prompt Received.


*-22,A
       Connected Device Error:
	Could Not Get Prompt.
    Device Did Not Respond Properly.

*-23,A
       Connected Device Error:
       No Response From Device.
 Check Serial Cable Or Modem Connection.

*-24,A
	      Comm Error:
      Error Opening Serial Port.


*-25,A
	      Comm Error:
      Error Closing Serial Port.


*-26,A
	     Error No. 026

     Could NOT Close Serial Port.
 Port Was Opened In Unsolicited Mode.
*-27,A
	     Error No. 027

	   Port IS NOT Open.

*-28,A
	     Error No. 028

       Connected Device Error:
     Unknown Response From Device.
*-29,A
	     Error No. 029
       Message Validation Error.
     Device Response Did Not Match
	  Expected Response.
*-30,A

     ERROR: Data Is Out Of Range.


*-31,A

		 ERROR
     Not A Valid Code Or Frequency.

*-32,A

		 ERROR
      Frequency Spacing Invalid.

*-33,A

		 ERROR
  Invalid Hexadecimal Digit Entered.

*-34,A

		 ERROR
       Invalid Command Entered.

*-35,A

		 ERROR
     Invalid Connect Tone Entered.

*-36,A

		 ERROR
      Invalid Frequency Entered.

*-37,A
	     FATAL ERROR !
	     ERROR No. 037
     Incorrect Codeplug Version Or
   'SWAPFILE.RSC' File Is Corrupted.
*-38,A
	     FATAL ERROR !
	     Error No. 038
RSS and Resource Files Are Incompatible
     Reinstall Latest RSS Version.
*-39,A
	     FATAL ERROR !
	     Error No. 039
    Problem Reading Resource Files.
     Reinstall Latest RSS Version.
*-40,A
	     FATAL ERROR !
	     Error No. 040
     Resource Files Are Corrupted.
     Reinstall Latest RSS Version.
*-41,A
	     Error No. 041
	Codeplug File Corrupt.
     Codeplug Checksum Incorrect.

*-42,A
	     Error No. 042

  Not Able To Encode Or Decode Data.

*-43,A
	     Error No. 043
	Corrupted Codeplug Data
  Read From File/Received From Device.
      S-Record Checksum Incorrect.
*-44,A
	     Error No. 044
	Corrupted Codeplug Data
  Read From File/Received From Device.
	  S-Record Corrupted.
*-45,A
	     Error No. 045

 A Non Hexadecimal Character Was Found
	 In The Current Field.
*-46,A
	     Error No. 046

   Not A Valid Codeplug File Format.

*-47,A

	   Empty Path String.
      Re-enter The Directory Name.

*-48,A

	   Illegal Path Name.
      Bad Character In Path Name.

*-49,A

	 File Length Incorrect.
	       Re-Enter.

*-50,A
      Too Many Files In Directory.
  Max No. Of Displayable Files Is 200.
  Delete Some Files Or Use Wildcards
      And Try Viewing Files Again.
*-51,A

       Error Creating Directory.
      Re-enter The Directory Name.

*-52,A

       Illegal Command Received
       By The Connected Device.

*-53,A

   Connected Device Checksum Failure 
  Occurred.  Retry Programming Device.

*-54,A
	   Connected Device 
	Could Not Be Programmed.
    Non Volatile Memory Move Failed.

*-55,A

	Invalid Activation Code.
	Check Code And Re-enter.

*-56,A

	   Codeplug Too Big.
 Please Delete Some Data And Try Again.

*-57,A

     Invalid Character In Filename.
   Please Correct Name And Re-enter.

*-58,A
	   Illegal RSS File.
	The File You Are Trying
   To View/Read Is NOT An RSS File.

*-59,A
	     Error No. 059
	Invalid Node Request !
  The Codeplug File May Be Corrupted!

*-60,A
	     FATAL ERROR !
	     Error No. 060
	 Unknown File Position.
	  Restart RSS Program.
*-61,A
	     FATAL ERROR !
	     Error No. 061
     Cannot Delete This Structure.

*-62,A
	     FATAL ERROR !
	     Error No. 062
     Cannot Modify This Structure.

*-63,A
	   Codeplug Data Has
	 Already Been Entered.

       Overwrite Existing Data?
*-64,A
	 A File With That Name
	    Already Exists.

       Overwrite Existing File?
*-65,A
	  Codeplug Not Loaded.
	 Please Load Codeplug
      Before Entering This Screen.

*-66,A
	     FATAL ERROR !
	     Error No. 066
      Cannot Delete The Specified
	Node From The Link List.
*-67,A
	     FATAL ERROR !
	     Error No. 067
   CSIT Table Must Be Loaded Before
  Continuation Of Program Is Allowed.
*-68,A

      Not Enough Memory Available
   To Add A New Section To Codeplug.

*-69,A
	     FATAL ERROR !
	     Error No. 069
    Link List Node Address Is NULL.
	  Cannot Delete Entry.
*-70,A
	     FATAL ERROR !
	     Error No. 070
       An Unknown Operation Was
      Attempted On The Link List.
*-71,A
  Alignment Cannot Be Performed Since
 HW Platform Is Not Quantar Or Quantro
 On The Hardware Configuration Screen.

*-72,A
	 Codeplug Is Too Large
   For The Connected Device To Handle.
    Removed Unused Information From
  Codeplug And Try Programming Device.
*-73,A
      Codeplug Read From File Or
   Received From Connected Device Has
	Illegal Addresses In It.
      Retry To Load The Codeplug.
*-74,A
    The Connected Device/RSS Did Not 
  Receive A Correct Codeplug Data Line.
     Comm Lines Could Be Too Noisy.
     Retry Current Operation Later.
*-75,A
       Connected Device CHKSUM On
	 Received Data Failed.
     Comm Lines Could Be Too Noisy.
     Retry Current Operation Later.
*-76,A
    Connected Device Could Not Move
       Codeplug From RAM To NVM.
     Comm Lines Could Be Too Noisy.
     Retry Current Operation Later.
*-77,A
    Connected Device Codeplug CHKSUM
       Of Entire Codeplug Failed.
     Comm Lines Could Be Too Noisy.
     Retry Current Operation Later.
*-78,A

      Access Table Does Not Exist.
   Number Must Be In The Range Shown.

*-79,A

    Delete Access Table Key Pressed.

       Do You Wish To Continue?
*-80,A

	 The Last Access Table
	   Cannot Be Deleted.

*-81,A

    Key Is Not Valid In This Field.
Please Move To Another Field And Retry.

*-82,A
  This Access Table Is Still In Use.
  Reassign Channel(s) Before Deleting
	This Access Code Table.

*-83,A
 Access Code Table Has Been Corrupted.
      Squelch Type And Code/Freq
	     Do Not Match.

*-84,A

    Squelch Type Does Not Match The
	   Entered Code/Freq.

*-85,A

     Add Access Table Key Pressed.

       Do You Wish To Continue?
*-86,A
	     Error No. 086
	  Internal RSS Error.
      Please Report This Problem
      To Motorola Service Center.
*-87,A
	  Command Entered Is
	 Not A Valid Command!
	Please Re-Enter Command.

*-88,A
  This Function Key Is Not Available
     On The Channel Number Field.
Please Move To Another Field To Execute

*-89,A
    The Maximum Number Of Channels
	   Currently Exists.
     No More Channels May Be Added.

*-90,A
  The Delete Channel Function Cannot
   Be Performed Since There Is Only
	   One Channel Left.

*-91,A
 Delete Channel Key Has Been Pressed.
   Current Channel Will Be Deleted.

       Do You Wish To Continue?
*-92,A
   Add Channel Key Has Been Pressed.
     Channel Will Be Added At End.

       Do You Wish To Continue?
*-93,A
 An Access Code Table Has Been Entered
	 Which Does Not Exist.
 Please Add Before Programming Device.

*-94,A
  The Frequency Entered Is Not Within
    Range Specified For This Band.

     Do You Wish To Correct This?
*-95,A
The Frequency Entered Is Not Divisible
	 By 5 kHz or 6.25 kHz.

     Do You Wish To Correct This?
*-96,A
  The Spacing Between The Highest Rx
   Frequency And Lowest Rx Frequency
 Exceeds 4MHz. See Help For More Info.
     Do You Wish To Correct This?
*-97,A
   The Maximum Number Of Access Code
       Tables Currently Exists.
No More Access Code Tables May Be Added

*-98,A
 This Alignment May Only Be Performed
    If Receiver Is In The VHF Band.
  See Hardware Configuration Screen.

*-99,A
 This Alignment May Only Be Performed
    If Exciter Is In The VHF Band.
   See Hardware Configuration Screen.

*-100,A
	 No Comments Have Been
	 Entered For This File.

    Do You Wish To Enter Comments?
*-101,A
	     FATAL ERROR !
	     Error No. 101
       Codeplug File Corrupted.
     Incorrect Offset Information.
*-102,A
   TRC/DC Information Is Non-Editable.
    To View/Edit TRC or DC Commands,
   Set Remote Control To TRC or DC
  And Station Type Can Not Be ASTRO !
*-103,A
      You Have Requested That The 
      Current Codeplug Be Saved To 
	 The Connected Device.
	Do You Wish To Proceed?
*-104,A
   MAXIMUM CODEPLUG LENGTH EXCEEDED.
Please Delete Some Entries In Codeplug
	   Before Continuing.

*-105,A

      Can't Copy File To Itself!
    Change Name of Destination File.

*-106,A
  This Function Key Is Not Available
     On The Repeater Number Field.
Please Move To Another Field To Execute

*-107,A
  Add Repeater Key Has Been Pressed.
    Repeater Will Be Added At End.

       Do You Wish To Continue?
*-108,A
    The Maximum Number Of Repeaters
	   Currently Exists.
    No More Repeaters May Be Added.

*-109,A
 Delete Repeater Key Has Been Pressed.
   Current Repeater Will Be Deleted.

       Do You Wish To Continue?
*-110,A
  The Delete Repeater Function Cannot
   Be Performed Since There Is Only
	  One Repeater Left.

*-111,A
	Intellirepeater Is Not
	  Currently Enabled.
  System Type Must Be INTELLIREPEATER
   On Hardware Configuration Screen.
*-112,A
     Connected Device Must Be Keyed
       Before This Procedure Can
	     Be Performed.

*-113,A
 This Screen Can Only Be Displayed If
 Intellirepeater Frequency Band Equals
	      VHF Or UHF
 On The Hardware Configuration Screen.
*-114,A
		 ERROR
	Invalid Time or Format.
	 Must Be The Following
	       HH:MM:SS
*-115,A

	   Invalid System ID.
      System ID Can Not Be "0000".

*-116,A
	     FATAL ERROR !
	     Error No. 121
	 Repeater Summary Data
     Could Not Be Internally Saved.
*-117,A
       A Desired Repeater Number
   Is Invalid Because It Exceeds The
      Number of Repeaters At Site
    Or It Has '0' as New Repeater #.
*-118,A
       A Desired Repeater Number
  Is Common To More Than One Repeater.
Blank Fields Default To Current Rptr #.
	 Please Check Entries.
*-119,A
   Reorder Repeaters Key Was Pressed.
     Repeaters Will Be Re-Arranged.

       Do You Wish To Continue?
*-120,A
	     FATAL ERROR !
	     Error No. 124
     A Node Position Was Not Found
      In The Given Re-Order Array.
*-121,A
   Zero Is Not a Legal Node Position
       Node Counts Start At '1'.
  Check Data Before Reordering Nodes.

*-122,A
      A Node Position Entered Is
 Greater Than Number of Existing Nodes.
  Check Data Before Reordering Nodes.

*-123,A
      A Node Position Entered Is
     Common To More Than One Node.
  Check Data Before Reordering Nodes.

*-124,A
	       WARNING 
      This RSS Application Is Not
      Released For Customer Use.
     Motorola Internal Use Only!!
*-125,A
	       WARNING
  This Connected Device's Software Is
    Not Released For Customer Use.
     Motorola Internal Use Only!!
*-126,A
    No Codeplug Has Been Downloaded
       To The Connected Device.
     Load a Codeplug Into Device
	  Before Reading it.
*-127,A
	       WARNING
   Printer Database File Not Found.
	Continue Using Default
	   Printer Values?
*-128,A
		 ERROR
	 Printer Device Could
	    Not Be Loaded.
       Do You Wish To Continue?
*-129,A
		 ERROR

      Printer Could Not Be Loaded.
	Do You Wish To Continue?
*-130,A
		 ERROR
	    Unable To Load
	     Default Font.
	Do You Wish To Continue?
*-131,A
		 ERROR
	Unable To Load Default
	     Graphic Mode.
       Do You Wish To Continue?
*-132,A
		 ERROR

     Unknown Printer Driver Error.
       Do You Wish To Continue?
*-133,A
	 You Have Requested To
      Reset The Connected Device.

       Do You Wish To Proceed ?
*-134,A
  Version String Has Invalid Format.

    The Connected Device Responded
	With An Illegal String.
*-135,A
   Codeplug Loaded In Connected Device 
	   Is Not Compatible 
	 With This RSS Version.
 Major Version Number Does Not Match !
*-136,A
   Codeplug Loaded In Connected Device
	   Is Not Compatible
   Compatible With This RSS Version.
    Please Use Latest RSS Version.
*-137,A
  This Function Key Is Not Available
	 On The Current Field.

 Please Move To First Field To Execute.
*-138,A
  This Function Key Is Not Available
	 On The Current Field.
     To Reset The Connected Device,
   Move To First Field and Try Again.
*-139,A
	The Tx Wireline Module
    Does Not Need Alignment Because
  The Automatic Level Control Option
   Has Been ENABLED In The Codeplug.
*-140,A
       One Of The Tx Gain Fields
	   Is Out Of Range.
 Please Check All Four Tx Gain Fields
   And Try Saving Their Values Again.
*-141,A
    The Connected Device Has Reset !
      The Front Panel Information
	  Currently Displayed
	Is Not Valid Any Longer.
*-142,A
	    This Field Does
     Not Require Alignment Because
       Spectratac Is Disabled !

*-143,A
	    This Field Does
     Not Require Alignment Because
	  Astro Is Enabled !

*-144,A
	       WARNING
  This Connected Device Firmware Is 
    Not Released For Customer Use.
     Motorola Internal Use Only!!
*-145,A
	     FATAL ERROR !
	     Error No. 145
     The Codeplug Data Can Not Be
   Upgraded To The Selected Version.
*-146,A
	The Codeplug Loaded Is
   The Latest Version For This RSS.

    You Can't Upgrade This Codeplug.
*-147,A
       Status Tone Is Disabled !
    This Field Can Not Be Accessed
      Because The Station Can Not
	Generate A Status Tone.
*-148,A
  This Is The First Set Of Messages !

      No Previous Set Of Messages
	   Can Be Displayed.
*-149,A
  This Is The Last Set Of Messages !

  The Connected Device Cannot Log More
    Messages Than Those Displayed.
*-150,A
	 You MUST Be Connected
	     To A Device
	  Before You Can View
	The Status Report Screen.
*-151,A
	 You MUST Be Connected
	     To A Device
	  Before You Can Run
	  Digital Metering !
*-152,A
     System Type Has Been Changed.
     Conventional System Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-153,A
     System Type Has Been Changed.
       Trunking System Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-154,A
     System Type Has Been Changed.
    Intellirepeater System Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-155,A
	 Token Repeater Number
     Has Been Changed By The RSS !
	Refer To RSS Manual or
    Site General Screen For Details.
*-156,A
      Remember To Save Any Codeplug
      Changes Before Exiting RSS!!

      Are You Ready To Exit To DOS?
*-157,A
	  Power Out Alignment
	       Has Been
	 Successfully Saved !

*-158,A
	 Rx Wireline Alignment
	       Has Been
	 Successfully Saved !

*-159,A
	 Tx Wireline Alignment
	       Has Been
	 Successfully Saved !

*-160,A

     Please Enter A Value Between
	  -50 dB And -105 dB.

*-161,A
	    RSSI Alignment
	       Has Been
       Successfully Calibrated !

*-162,A
	   Squelch Alignment
	       Has Been
	 Successfully Saved !

*-163,A
    Reference Oscillator Alignment
	       Has Been
	 Successfully Saved !

*-164,A
	Tx Deviation Alignment
	       Has Been
	 Successfully Saved !

*-165,A
    Reference Modulation Alignment
	       Has Been
	 Successfully Saved !

*-166,A
	       WARNING
  Could Not Read Current TX Deviation
    Settings From Connected Device.

*-167,A
       A Trunking (6809) System
      Can Only Have One Channel.
	You Can't Add Channels
	  To This Codeplug !
*-168,A
 This Alignment May Only Be Performed
      On Trunking (6809) Systems
    That Are Not Simulcast Enabled.
  See Hardware Configuration Screen.
*-169,A
       TDATA Deviation Alignment
	       Has Been
	 Successfully Saved !

*-170,A
     No Wireline Has Been Selected.
     You Cannot View This Screen.

   See Hardware Configuration Screen.
*-171,A
       The System Type Selected
	Is Not TRUNKING (6809)
     You Cannot View This Screen. 
   See Hardware Configuration Screen.
*-172,A
    Remote Control Is Non-Editable.
 To View/Edit Remote Control Commands,
	Set Wireline To 4-Wire.

*-173,A
     Serial Number Does Not Match
	Station Serial Number!

     Overwrite Station Codeplug?
*-174,A
		 ERROR
    You Are Not Allowed To Have More
     Than 4 Repeaters With Voice On
	    Control Enabled.
*-175,A
		 ERROR
    You Are Not Allowed To Have More
     Than 4 Channels With Voice On
	    Control Enabled.
*-176,A
		 ERROR
      You Can Not Have The Pended
     Emergency Request Time Greater
      Than The VOC Activation Time.
*-177,A
		 ERROR
   The Pended Emergency Request Time
   Must Be At Least 500 Milliseconds
   Less Than The VOC Activation Time.
*-178,A
		 ERROR
	 You Can Not Have More
	 Than 4 Channels With
	Voice On Control Enabled.
*-179,A
		 ERROR
	 You Can Not Have More
	 Than 4 Repeaters With
	Voice On Control Enabled.
*-180,A

    TRC/DC Information Is Non-Editable
	  For Trunking Systems.

*-181,A
  UHSO Reference Oscillator Alignment
	      Has Been
	 Successfully Saved !

*-182,A
   Exiting This Alignment Screen Will
     Abort The Auto-Net In Progress!

	      Continue?
*-183,A
      Auto-Net Has Been Aborted.

	  Internal Reference
	 Has Not Been Aligned.
*-184,A

 Connected Device Is Already Executing
	  Auto-Net Procedure.

*-185,A
    The Auto-Net Procedure Failed.

	  Internal Reference
	 Has Not Been Aligned.
*-186,A
    The Auto-Net Procedure Complete

	  Internal Reference
     Has Been Successfully Aligned.
*-187,A
		 ERROR
	 You Already Have The
	 Maximum of 32 Blocks.

*-188,A
		ERROR
	 LOW ID Must End In 0.
	   Please Re-enter.

*-189,A
		ERROR
	 HIGH ID Must End In F.
	   Please Re-enter.

*-190,A
		ERROR
	 No Blank ID's Allowed.
	 Please Enter Valid ID
	      Or Abort.
*-191,A
		ERROR
	 Low ID Must Be Less
	  Than The High ID.
	   Please Re-Enter.
*-192,A
		ERROR
	  You Cannot Delete
	 The Last Band Range.

*-193,A

  Connected Device May Not Be Keyed-Up
     During The Auto-Net Process.

*-194,A
     Connected Device May Not Be
     Dekeyed During The Auto-Net
	       Process.

*-195,A
     System Type Has Been Changed.
	DSSIII System Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-196,A
	       WARNING
You Are About To Overwrite The Connected
Device's Codeplug With An Older Version.  
       Do You Wish To Overwrite?
*-197,A
	     ERROR No. 197

     This Feature Is Not Supported
    With Current Version Of Codeplug
*-198,A
  Wireline Operation Has Been Changed.
	    8 Wire Defaults
	     Will Be Used.
	Do You Wish To Continue?
*-199,A
  Wireline Operation Has Been Changed.
	    6 Wire Defaults
	     Will Be Used.
	Do You Wish To Continue?
*-200,A
	       WARNING
Setting MCS To MULTI-PL ONLY Will Clear
  The Channel And Access Code Tables.
       Do You Wish To Continue?
*-201,A
	       WARNING
   Setting MCS To DISABLED Will Delete
	 All MCS Information.
       Do You Wish To Continue?
*-202,A
  The MCS User Information Has Changed!
 The MCS Accounting Information Will Be
 Cleared If This Codeplug Is Downloaded.
       Do You Wish To Continue?
*-203,A
	  This Will Clear All
       MCS Accounting Information
	   In Station Memory.
	Do You Wish To Continue?
*-204,A

       MCS Accounting Information
     Has Been Successfully Cleared.

*-205,A
       The PL Code Entered Is Not
Compatible With A Previously Entered PL.
  Please See The List Of Incompatible
       PL Codes In The Help Text.
*-206,A
     An Rx PL or DPL Code Cannot Be
   Used For More Than One User Entry.

  Please Select Another PL or DPL Code.
*-207,A
    The PL Frequency Entered Is Not
Compatible With A Previously Entered PL.
  Please See The List Of Incompatible
    PL Frequencies In The Help Text.
*-208,A
       An Rx PL Frequency Cannot Be
    Used For More Than One User Entry.

   Please Select Another PL Frequency.
*-209,A
    There Is A Maximum Of 12 Rx PLs
      And 1 Rx DPL For This Table.

  Please Make The Appropriate Changes.
*-210,A
  You Have Specified That All MCS Table
	 Entries Will Be Deleted.
   The MCS Table Must Contain At Least
     One Entry For Proper Operation.
*-211,A
   BSI And Control Channel Capability
	 Cannot Both Be ENABLED
	    On Any Repeater.
      Correct Before Disabling VOC
*-212,A
    Hanging Up Will Disconnect from
	   The Remote Modem

       Do You Wish To Continue?
*-213,A
	The Modem Is Online.
     Do You Wish to Disconnect From 
	  The Remote Modem?

*-214,A

  The RSS Has Successfully Connected
	To The Remote Device.

*-215,A
		ERROR
 RSS Has Connected to Remote Modem But
   Device Is Not Responding. Remote
   Modem May Be Improperly Configured.
*-216,A
		ERROR
  RSS Cannot Initialize The Local Modem.
 Ensure Initialization String Is Correct
     And Modem is Connected To Port.
*-217,A
	       WARNING
 RSS Is Currently Online With A Remote
    Modem. Do You Wish To Hang Up And
	Dial Selected Number?
*-218,A
		ERROR
      The Selected Entry Does Not
    Contain A Phone Number. Correct
	  Before Continuing.
*-219,A
		
     The New Password Has Been Set.


*-220,A
	The Connected Device Is
	  Password Protected.
    You Must Enter A Valid Password
   Before You Can Access The Device.
*-221,A

 Password Protection Has Been Disabled.


*-222,A
	       WARNING
    Access Code Table Used By This 
  Channel Is Not Using PL. Correct On
 ACT Screen Before Programming Station.
*-223,A
	       WARNING
    Deleting This Channel Has Caused
   The Startup Channel To Be Set To 1.

*-224,A
   Alignment Cannot Be Performed Since
 Hardware Platform Is Astro-TAC Receiver
   On The Hardware Configuration Screen.

*-225,A
  Hardware Platform Has Been Changed.
      PA And Channel Tx Settings
    Will Change To Default Values.
       Do You Wish To Continue?
*-226,A
   Alignment Not Allowed Since Hardware
  Platform Is Quantar Satellite Receiver
   On The Hardware Configuration Screen.

*-227,A
	       WARNING
      For DSSIII, Cold/Warm Start
    Diagnostics Are Not Functional
      And Will Not Be Executed.
*-228,A
      Alignment Cannot Be Performed
	 Since Station Type Is
	   Not Astro Capable

*-229,A

	  This Key Not Allowed
	  For Trunking Systems.

*-230,A
     System Type Has Been Changed.
   Quantar Data Base Station System
	Defaults Will Be Used.
       Do You Wish To Continue?
*-231,A
   The Station Is Set Up For Astro.
	  This Screen Is Not
	  For Astro Stations.

*-232,A
       The System Type Selected
	 Is Not CONVENTIONAL.
     You Cannot View This Screen.
  It Is Only For Conventional Stations.
*-233,A
      The Codeplug In Memory Is An
      Old Version.  It Needs To Be
	 Upgraded Before It Can
	  Support This Feature.
*-234,A
	     You Cannot Have
	Scanning Receiver Active
	When MultiCoded Squelch
	      Is Enabled.
*-235,A
    The Tx Wireline Module Does Not
    Need Alignment Because Automatic
  Level Control Is ENABLED And Wireline
   Squelch is DISABLED In The Codeplug.
*-236,A
      Toggling Remote Control Type 
	 Will Set The New Remote
 Control Command Table To It's Default.
       Do You Wish To Continue?
*-237,A

	 HLGT Frequency Must Be
	    Divisible by 5.

*-238,A

       No Channels Are Programmed
	  To Use This Receiver.

*-239,A
	       ERROR
	You Cannot Program A
	Quantar Codeplug Into
     An AstroTAC 3000 Comparator.
*-240,A
	       ERROR
	You Cannot Program An 
   AstroTAC 3000 Comparator Codeplug 
     Into A Quantar Base Station.
*-241,A
	The Codeplug Has Been
     Successfully Programmed Into
	The Connected Device.

*-242,A
	The Codeplug Has Been
      Successfully Saved To Disk.


*-243,A
	  The Codeplug Has Been
	 Successfully Read From
	  The Connected Device.

*-244,A
	The Codeplug Has Been
     Successfully Read From Disk.


*-245,A
       Wildcard Partition On
     Disk Successfully Merged
	  Into Codeplug.

*-246,A
	       WARNING
  Deleting This Channel Has Caused
   The Scanning Priority Channel
	 To Be Set To NONE.
*-247,A

 Spaces Are Not Allowed In This Field.
	 Please Modify Entry.

*-248,A
		ERROR
       Invalid Address Entered.


*-249,A

   You Cannot Perform Digital Metering
    With An AstroTAC 3000 Comparator.

*-250,A

      Analog Link Timer Must Be
	   Divisible by 10.

*-251,A

     You Cannot Perform Diagnostics
    With An AstroTAC 3000 Comparator.

*-252,A
	The System Type Selected
	  Is Not CONVENTIONAL.
      You Cannot View This Screen.
   See Hardware Configuration Screen.
*-253,A
	The System Type Selected
	   Is Not SMARTZONE.
      You Cannot View This Screen.
   See Hardware Configuration Screen.
*-254,A
The Frequency Entered Is Not Divisible
     By 2.5kHz, 5 kHz or 6.25 kHz.

     Do You Wish To Correct This?
*-255,A
     System Type Has Been Changed.
       SmartZone System Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-256,A
	Accessing Wildcard Data
	Is Not Applicable For An
   AstroTAC 3000 Comparator Codeplug.

*-257,A
	   Scanning Receiver
	   Is Set To Disabled.

 You Cannot View Or Edit Scanning Info.
*-258,A

       Cannot Perform Operation
    WL Equalization Set To DISABLED

*-259,A
		ERROR

	Invalid Time Value Entered.

*-260,A
		ERROR

	Invalid Date Value Entered.

*-261,A
	Do You Wish To Crossload
     The Codeplug To Other Stations
	      At The Site?

*-262,A
	  Do You Wish To Reset
       All Stations At This Site?


*-263,A
    The IP Address Was Successfully
	 Saved To The Device.
   The Physical Address Was Not Saved
	 Based On Your Selection.
*-264,A
	 Accessing the Ethernet
   Parameters Screen Is Only Applicable
     With An AstroTAC 3000 Comparator.

*-265,A
		ERROR
      FTP Software Timed Out While
  Trying To Communicate With Device.

*-266,A
    Would You Like To Set The Date
       And Time At All Stations
	     At The Site?

*-267,A
    The Device You Are Connected To
       Is Incompatible With This
	  Version Of The RSS.

*-268,A
       The Codeplug File You Are
	  Attempting To Read
       Is Incompatible With This
	  Version Of The RSS.
*-269,A
		ERROR
     One Or More Files Are Missing
 From The Firmware Download Directory.

*-270,A
		ERROR
       Firmware Download Aborted
      Due To Backplane ID Mismatch.

*-271,A
Warning: Downloading might take a while
 and channel performance might degrade.
 Do this only if Requested by Motorola.
	      CONTINUE?
*-272,A
     An Error Occurred While Writing
	     To The File.
  Could Not Write Entire File to Disk.

*-273,A
       Alerts Report Successfully
	     Saved To Disk.


*-274,A
		 ERROR
	 The Timestamp That Is
	Being Assigned For This
     Firmware Download Is Invalid.
*-275,A
   Changing The Physical Address May
       Cause System Malfunction!
       Are You Sure You Want To
      Save the Physical Address?
*-276,A
      The IP Address And Physical
       Address Were Successfully
	  Saved To The Device.

*-277,A
	 Accessing the Program
    Firmware Screen Is Only Applicable
	 With A Station Codeplug.

*-278,A
	 Accessing the Ethernet
   Parameters Screen Is Only Applicable
	 With A Station Codeplug.

*-279,A
    The Firmware Download Procedure
	   Has Been Aborted.


*-280,A
      There Are No Valid Firmware
    Download Directories Located At
	    C:\MRSS\QUANTAR 

*-281,A
		 ERROR
       Unable To Display Firmware
  Download Directory Choice List Menu.

*-282,A
     There Is No Modem Connection.
       Modem Must Be Online To
	    Send String.

*-283,A
 WARNING: You Have Left The Comparator
	 In Local Control Mode.
 This Disables Remote Control Commands.
       Do You Still Wish To Exit?
*-284,A
    Command To Put Connected Device
  Into Normal Operating Mode Was Sent.


*-285,A
	 Device Already Is In
	 Normal Operating Mode.
	   Command Not Sent.

*-286,A
		WARNING!
      Status Report Not Retrieved.
   Device Is In Normal Operating Mode.
   View Log Via Status Report Screen.
*-287,A
       Status Report Successfully
    Retrieved From Connected Device.


*-288,A
		 ERROR!
	You Must Select A Valid
       Firmware Directory Before
       Performing This Operation.
*-289,A
		 ERROR!
    You Have An Invalid SWDL.INI file
   In Your Firmware Download Directory

*-290,A
	Requested Test Tone
	  Was Not Started.

      See Error Log For Detail.
*-291,A
		 ERROR!

   One Or More FTP Files Are Missing.
*-292,A
     Comparator Type Has Been Changed.
     Standard Comparator Type Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-293,A
     Comparator Type Has Been Changed.
     Expanded Comparator Type Defaults
	     Will Be Used.
       Do You Wish To Continue?
*-294,A

      You Cannot Enter The Analog
     Voting Parameters Screen When
    The Comparator Type Is Expanded.
*-295,A

       You Cannot Enter The Local
      Status Screen if Your Chassis
	 Number is not Primary.
*-296,A
	    ADVISORY WARNING!
 An int. UHSO or an ext. ref. UHSO is
 needed for optimum station performance
 in the 12.5 kHz channel spacing mode.
*-297,A
      There Are No Valid Firmware
    Download Directories Located At
	    C:\MRSS\ASTROTAC
*-298,A
      You Need To Reset Device
    In Order For The New Value(s)
	   To Take Effect.
*-299,A
     The Port Control Parameters
      Screen Can Only Be Viewed
      From The Primary Chassis
*-300,A

     You Have Specified An Invalid
	      Timer Value.
	 Valid Values are 1-10.
*-301,A

     You Have Specified An Invalid
	Access Code Table Value
	 Valid Values are 1-16.
*-302,A

     You Have Specified An Invalid
	    Channel Value
	 Valid Values are 1-16.
*-303,A

     You Have Specified An Invalid
	       Channel Value
	 Valid Values are 1-16.
*-304,A

     You Have Specified An Invalid
	     Event Flag To Clear.
	 Valid Values are 1-16.
*-305,A

     You Have Specified An Invalid
	     Output To Clear.
	 Valid Values are 1,2,3,7.
*-306,A

     You Have Specified An Invalid
	    Output To Clear.
	 Valid Values are 1-10.
*-307,A

     You Have Specified An Invalid
	Clear SAM Spi Bit Value.
	 Valid Values are 3-5.
*-308,A

     You Have Specified An Invalid
	    Current Channel.
	 Valid Values are 1-16.
*-309,A

     You Have Specified An Invalid
	    Current Channel.
	 Valid Values are 1-16.
*-310,A

     You Have Specified An Invalid
	   Event Flag Value.
	 Valid Values are 1-16.
*-311,A

     You Have Specified An Invalid
		 Input       
       Valid Values are 1-7,9.
*-312,A

     You Have Specified An Invalid
		 Input
	 Valid Values are 1-12.
*-313,A

     You Have Specified An Invalid
	    MCS User Number.      
	Valid Values are 1-13.
*-314,A

     You Have Specified An Invalid
	      Output Value.
       Valid Values are 1,2,3,7.
*-315,A

     You Have Specified An Invalid
	      Output Value.
	 Valid Values are 1-10.
*-316,A

     You Have Specified An Invalid
	   Sam Command Value.      
	 Valid Values are 0-15.
*-317,A

     You Have Specified An Invalid
	   Event Flag To Set.
	 Valid Values are 1-16.
*-318,A

     You Have Specified An Invalid
	     Output To Set.
	 Valid Values are 1,2,3,7.
*-319,A

     You Have Specified An Invalid
	     Output To Set.
	 Valid Values are 1-10.
*-320,A

     You Have Specified An Invalid
	  SAM SPI Bit To Set.
	 Valid Values are 3-5.
*-321,A

     You Have Specified An Invalid
	    Timer To Abort.
	 Valid Values are 1-10.
*-322,A

     You Have Specified An Invalid
	   TRC Function Tone. 
	 Valid Values are 1-15.
*-323,A

      You Have Specified An Invalid
	    TRC Tone Value.
	 Valid Values are 1-15
*-324,A
	You Have Specified An
	    Invalid Value.
	 Values Must Be Less
	     Than 65535.
*-325,A

     This Command Requires A Value.
	 Please Enter A Value.
     
*-326,A
	  
	   The Value For This
       Command Must Not Be Blank.
	  Please Enter A Value.    
*-327,A
       You Have Specified An
	Invalid Table Number.
	   Please Retry.

*-328,A

	 You Are Already At The
	      First Table.
	     
*-329,A

	 You Are Already At The
	      Last Table.
	     
*-330,A
	You Are About To Lose
	  All Existing Data.
     Are You Sure That You Want To
	 Set To The Default?
*-331,A

	Are You Sure You Want To
	   Delete This Table?

*-332,A
       This Is The Only Table And
	  You Cannot Delete It.
	  Do You Want To Set It
	     To A Null Table?
*-333,A
  There Are No More Commands To View In
This Table. You Cannot Add More Commands
    Unless The NEXT TABLE Command Is
     The Last Action Or Inaction.
*-334,A

      This Group Has Overlap With
      Another Group On The Screen.
     Please Make Another Selection.
*-335,A

       Basic WildCard Allows Only
	 One Group For Outputs.

*-336,A

 WildCard Is Disabled In This Codeplug.
     There Is No WildCard Data To
	    View Or Edit.
*-337,A

       Basic WildCard Allows Only
	  One Group For Inputs.

*-338,A

   Active Level Must Not Be Blank.


*-339,A

    You Have Specified An Invalid
	WAIT Length Of Time. 
      Valid Values are 1-1000.
*-340,A

    You Have Specified An Invalid
	    HLGT ON Value.
      Valid Values are 1-1000.
*-341,A
       Setting Wireline To NONE
	Will Disable WildCard.

       Do You Wish To Continue?
*-342,A
       Setting Wireline To 4-WIRE
    Will Change Your WildCard Tables.

       Do You Wish To Continue?
*-343,A
    Setting WildCard To DISABLED Will
   Disable All Of Your WildCard Tables.

       Do You Wish To Continue?
*-344,A
     Setting WildCard To BASIC Will
      Delete All Of Your WildCard 
     State-Condition/Action Tables.
       Do You Wish To Continue?
*-345,A
   The Commands Added To This Table
 Have Caused You To Exceed The Length
     Of The WildCard Codeplug.
   Please Eliminate Some Of Them.
*-346,A
     You Will Exceed the Length
      Of The WildCard Codeplug
	By Adding This Table.
	  Cannot Add Table.
*-347,A
      You Are Nearly At The Limit
     Of The WildCard Codeplug Size
    By adding this table.  You Will
   Not Be Able To Fill All Commands.
*-348,A

       You Cannot Have An Embedded
	 Blank In A Value Field.

*-349,A

       You Have Disabled WildCard.

   Do You Wish To Preserve The Tables?
*-350,A
   You Have Typed In An Invalid State.
	 Please Re-Enter It
		OR
       Hit F2 For The Choice List.      
*-352,A

	 The NEXT TABLE Command
     Can Only Be Entered In The Last
      Action Or InAction Positions.
*-353,A
      The Codeplug In Memory Is An
     Older Version That Needs To Be
  Upgraded Before A WildCard Partition
	 May Be Merged Into It.
*-354,A
   The WildCard Operation Field Is Set   
  To Disabled In The Codeplug In Memory.
  You Cannot Merge A WildCard Partition
  While WildCard Operation Is Disabled.
*-355,A
 You Are Attempting To Merge An ENHANCED
 WildCard Partition Into A Codeplug That
       Has WildCard Set To BASIC.
	 No Merge Can Be Done. 
*-356,A
 You Are Attempting To Merge A DISABLED
   WildCard Partition Into A Codeplug.
       
	 No Merge Can Be Done.
*-357,A
      The File You Chose Does Not
       Have A WildCard Partition.

	 No Merge Can Be Done. 
*-358,A
		ERROR
 Connected Device's Codeplug Is Corrupt!
	 The WildCard Partition
	      Is Missing!
*-359,A
 Because Of Changes You Have Made, The
  WildCard Tables May Contain Commands
That Are No Longer Used By Your Station.
  Please Review Your WildCard Tables.
*-360,A
   You Have Set This Field To DISABLED
 Continuing Will Delete Any Main/Standby
 Tables From The Current Set of WildCard
     Tables.   Continue?
*-361,A
	 Continuing Will Add The
	 Default MAIN Tables To
   The Current Set of WildCard Tables.
	       Continue?
*-362,A
This Field Was Set To STANDBY.Continuing
 Will Replace The WildCard Main/Standby 
 Tables With The Default MAIN Tables.
	       Continue?
*-363,A
	 Continuing Will Add The
	Default STANDBY Tables To
   The Current Set of WildCard Tables.
	       Continue?
*-364,A
 This Field Was Set To MAIN. Continuing
 Will Replace The WildCard Main/Standby
 Tables With The Default STANDBY Tables.
	       Continue?
*-365,A
Programing WildCard with OUTPUT 2 causes
Audio problems for certain hardware. See
Help Text or User manual for details.
	       Continue?
*-366,A
Using groups containing OUTPUT 2 causes
Audio problems for certain hardware. See
Help Text or User manual for details.
	       Continue?
*-367,A
	       WARNING
	Mis-Use Of This Feature
      Will Cause Coverage Problems.
       Read Help Text For Details.


*-500,A

	 Host Error Received:
   Alignment Area Already Allocated.

*-501,A

	 Host Error Received:
    Codeplug Area Already Allocated.

*-502,A

	 Host Error Received:
       Bogus DSP value Received.

*-503,A

	 Host Error Received:
   Unable To Allocate Requested Size.

*-504,A

	 Host Error Received:
 Unable To De-Allocate Alignment Area.

*-505,A

	 Host Error Received:
  Unable To De-Allocate Codeplug Area.

*-506,A

	 Host Error Received:
 Download Aborted: One Was In Progress.

*-507,A

	 Host Error Received:
 Download Aborted: One Was In Progress.

*-508,A

	 Host Error Received:
      First Issue A GO Subcommand.

*-509,A

	 Host Error Received:
  A Required Task Has Not Responded!

*-510,A

	 Host Error Received:
	Internal Software Error.

*-511,A

	 Host Error Received:
	   Invalid Argument.

*-512,A

	 Host Error Received:
     Wrong # Of Chars For Argument.

*-513,A
	    Error No. 513
   Connected Device Does Not Support
	    This Feature.
     See System Help For More Info.
-514,A

	 Host Error Received:
   Invalid Decimal Integer Supplied.

*-515,A

	 Host Error Received:
  Invalid Hexadecimal Number Supplied.

*-516,A
	    Error No. 516
   Connected Device Does Not Support
	    This Feature.
     See System Help For More Info.
*-517,A

	 Host Error Received:
	   Option Is Invalid.

*-518,A

	 Host Error Received:
  Invalid Signed Decimal Int Supplied.

*-519,A

	 Host Error Received:
	   Invalid S-Record.

*-520,A

	 Host Error Received:
       Invalid S-Record Checksum.

*-521,A

	 Host Error Received:
	Input Level Is Too High.

*-522,A

	 Host Error Received:
	Input Level Is Too Low.

*-523,A

	 Host Error Received:
	   Missing Argument.

*-524,A

	 Host Error Received:
 Alignment Area Has Not Been Allocated.

*-525,A

	 Host Error Received:
 Codeplug Area Has Not Been Allocated.

*-526,A

	 Host Error Received:
      Arguments Are Out Of Order.

*-527,A

	 Host Error Received:
 One Or More Arguments Is Out Of Range.

*-528,A

	 Host Error Received:
   Pendulum Adjustment Beyond Limits.

*-529,A

	 Host Error Received:
       Too Many Bytes Requested.

*-530,A

	 Host Error Received:
    Too Many Arguments On One Line!

*-531,A

	 Host Error Received:
      Unexpected Opcode Received.

*-532,A

	 Host Error Received:
       Unsupported S-record type.

*-533,A
	    Error No. 533
   Connected Device Does Not Support
	    This Feature.
     See System Help For More Info.
*-534,A

	 Host Error Received:
Unable To Adj To Ambient Squelch Level.

*-535,A

	 Host Error Received:
 Unable To Obtain A Valid A_To_D Value.

*-536,A

	 Host Error Received:
	 Unable To Calibrate.

*-537,A

	 Host Error Received:
   Bogus Value Within Task Response.

*-538,A

	 Host Error Received:
      Backplane ID Not Available.

*-539,A

	 Host Error Received:
      Invalid Date Specification.

*-540,A

	 Host Error Received:
      Invalid Time Specification.

*-541,A

	 Host Error Received:
	Invalid Metering State.

*-542,A

	 Host Error Received:
       Invalid Metering Argument.

*-543,A
	 Host Error Received:
     Metering Task Already Running.
     Can't Start 2nd Metering Task.

*-544,A
	 Host Error Received:
  WireLine Board Disabled/Not Present.
	Cannot Run Metering Task.

*-545,A
	 Host Error Received:
      Transmitter Board Disabled.
	Cannot Run Metering Task.

*-546,A
	 Host Error Received:
	Receiver Board Disabled.
	Cannot Run Metering Task.

*-547,A
	 Host Error Received:
     A Tx/PA Problem Has Prevented
  The Connected Device From Keying Up.

*-548,A
	 Host Error Received:
      Invalid Number Of Arguments.
     Too Many or Too Few Arguments
	Passed With The Command.
*-549,A
	 Host Error Received:
 Connected Device Was Unabled To Obtain
	 A Valid Current Value.

*-550,A
	 Host Error Received:
   The Connected Device Must Have A
     Valid Codeplug Loaded Before
	  It Can Be Aligned.
*-551,A
	 Host Error Received:
 Unable To Start OverDrive Calibration
   Device Has Problems With: Tx Lock,
     Tx Holdoff, And/Or Tx Inhibit.
*-552,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
	   Tx Lock Inactive.

*-553,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
	   Tx Holdoff Active.

*-554,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
	Transmit Inhibit Active.

*-555,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
	    PA Fail Active.

*-556,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	  Final PA VSWR Alarm.
*-557,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	  Final Tx VSWR Alarm.
*-558,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	 Open Power Loop Alarm.
*-559,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	   Power Level Alarm.
*-560,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	No Forward Power Alarm.
*-561,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	 PA Temperature Alarm.
*-562,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	  PA Low Supply Alarm.
*-563,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	     PA Fan Alarm.
*-564,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	     Tx Lock Alarm.
*-565,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
       Connected Device Reports A
	Circ Temperature Alarm.
*-566,A
	 Host Error Received:
     Unable To Calibrate Overdrive.
     Connected Device Did Not Stay
	  Keyed For 2 Seconds.
*-567,A
	 Host Error Received:
	Unable To Align Due To
   Simulcast and/or 1pps Not Active.

*-568,A
	 Host Error Received:
     Corrupt Floating Point Number
     Sent To The Connected Device.

*-569,A
	 Host Error Received:
     A Tx/PA Problem Has Prevented
   The Connected Device From Dekeying.

*-570,A
	 Host Error Received:
	Input Level Is Unknown.


*-572,A
	 Host Error Received:
     UHSO Adjustment Has Reached
	   The Outer Limit.

*-573,A
	 Host Error Received:
     Unable To Lock Pendulum To The
	  External Reference.

*-574,A
      The Station Does Not Contain
	   A Valid Codeplug.
       A Codeplug Must Be Loaded
And The Connected Device Must Be Reset.
*-575,A

   The Password You Have Entered Does
Not Match The Connected Device Password.

*-576,A
   Valid Passwords Are Five To Eight
	 Characters In Length.

	 Password Not Accepted.
*-577,A

     The Password You Have Entered
      Contains Illegal Characters.

*-578,A
     The Password You Have Entered
	 Is A Reserved Keyword.

	 Password Not Accepted.
*-579,A
    The Password You Have Entered Does
   Not Match The One You First Entered.

	 Password Not Accepted.
*-580,A
       You Have Entered Too Many
	  Incorrect Passwords.
   Connected Device Will Be Disabled
	      For 1 Minute.
*-581,A
	 Host Error Received:

  Invalid Codeplug Download Command.

*-582,A
    Wildcard Download In Progress.

      All Downloads Now Aborted.

*-583,A

  Wildcard Area Already Allocated.


*-584,A

Wildcard Area Has Not Been Allocated.


*-585,A
	 Host Error Received:

     Receiver Board Is Disabled.
      You Can Not Run Metering.
*-586,A
	 Host Error Received:

  This Is The Wrong Port To Execute
	 The DOAYNC Command.
*-587,A
	 Host Error Received:

Executing the DOAYNC Command Is Only
 Valid On Intellirepeater Stations.
*-588,A
	 Host Error Received:

      Invalid Timestamp Format.

*-589,A
	 Host Error Received:

      Invalid Protocol Setting.

*-590,A
	 Host Error Received:

      Invalid Baud Rate Setting.

*-591,A
	  Host Error Received:
      Requested Timestamp Is Equal
   Or Older Than Device's Timestamp.
      Device Timestamp = UNKNOWN
*-592,A
	  Host Error Received:

	 Invalid Debug Command.

*-593,A
	  Host Error Received:

	Cannot Crossload Codeplug.

*-594,A
	  Host Error Received

      Cannot Execute The Command
	While In RSS Only Mode.
*-595,A
	  Host Error Received:

	Rx Signal Not Detected.
	      Check Setup.

